Our Connecting Flue Pipes can be colour coded to match your installation, and are used to connect from the appliance to the chimney system, which could be either a chimney liner, stack or twin wall flue system.
Enamel Premium (click to enlarge)
Vitreous enamelled connecting flue pipe
Startinox (click to enlarge)
0.6mm stainless steel connecting flue pipe
Ventilated Cover Pipe (click to enlarge)
Heat shield for connecting flue pipes
If your property has an existing chimney then a flexible flue liner is often the most recommended flue system to install. It is cost-effective, and utilises the current fireplace installation in the property.
The Poujoulat stainless steel flexible flue liners are designed for lining the existing flue or masonry chimney. Therefore, these are suitable for gas, oil and multi fuel installations.
316L and 904L are the two grades available. 904L is a higher grade making it suitable for the conditions found with coal based solid fuel installations.
Starflex (click to enlarge)
This flexible flue liner is perfect for the renovation of existing masonry chimneys with offsets, for multi-fuel and wood burning stoves.
Diameter: Ø125, Ø150, Ø180 & Ø200
Available as: Cut lengths, Ecofilm coils and de-coiling box.
Tubinox GF (click to enlarge)
Single skin Gas flexible liner
This flexible flue liner is perfect for the renovation of existing masonry chimneys with offsets connected to any type of gas fire.
Diameter: Ø100, Ø130, Ø150, Ø180 & Ø200
Available as: Cut lengths, Ecofilm coils and de-coiling box.
Single wall (click to enlarge)
Single wall multi fuel flue pipe
Single wall pipe which can be used as a liner to an existing brick stack and / or a connecting flue pipe for solid fuel appliances and as a chimney system for gas and oil appliances.
Diameters: Ø100, Ø130, Ø150, Ø180, Ø200 & Ø250.
If the property does not have an existing chimney, or an extension has been added to the property, insulated twin wall flue systems are used.
There are two installation methods for twin wall flue systems. The first being straight up through the ceilings and floors of the property. The system then exists through either a flat or pitched tiled roof.
The other method has exit points at either 45° or 90°, usually from an external wall, and the flue system then continues up the outside of the property. This method is also suitable if there is an attached single-story building (for example a garage). The flue system exists the main property into the garage, and then exists through the garage roof.
Not all stoves can use this method, but the TJS Installations sales team will guide you through the process.
Therminox (click to enlarge)
30mm insulated twin wall multi-fuel system chimney
This high quality twin wall insulated chimney system is designed for use with all solid fuel, wood, coal, gas, oil and pellet heating appliances.
Available as TI with a bright polished stainless steel outer case and for internal use our ZI has a galvanised steel outer casing.
Diameters: Ø100, Ø130, Ø150, Ø180, Ø200 & Ø250
Efficience (click to enlarge)
20mm insulated triple wall system chimney for wood burning stoves
This is a concentric insulated chimney with mineral wool insulation allowing the connection of combustion air and the smoke exhaust. Designed to operate safely with the latest generation of high efficiency wood burning stoves. Suitable for use in all types of air tight housing, new build or renovation projects.
This chimney system works in negative pressure and optimises the appliance’s efficiency and can be used on top or rear connection appliances.
Diameters: Ø100, Ø130, Ø150, Ø180 & Ø200.
Dualinox (click to enlarge)
25mm insulated twin wall multi-fuel system chimney
With a simple range of chimney components & supports, this insulated twin wall multi-fuel system chimney is mainly suitable for installing externally to the building.
Diameters: Ø130 & Ø150
We can supply the entire range of accessories necessary for the installation of Chimneys and Flues. Air Vents, Smoke Pellets, Thermometers, High Temperature Spray Paint, Rubber Flashing and much more.
Get in touch with TJS Installations by calling 01604 402916 or fill out our enquiry form here.
Duo-Gas (click to enlarge)
Concentric flue system for balanced gas fires
Designed for gas fired room-sealed appliances. Brings the combustion air in and also evacuates the smoke, and can also be used as a conventional gas vent.
Ideal for the new build market it can terminate vertically through the roof or horizontally through the wall. Can easily be connected to an existing chimney lined with our Tubinox Gas Flex liner using the Renovation Kit.
Diameters: Ø100/150, Ø130/200 & Ø150/200
PGI Pellet (click to enlarge)
Concentric flue system for pellet stoves
New generation of chimney optimises the appliance efficiency where energy saving and thermal improvement are the aim.
Diameters: Ø100/150 & Ø130/200.
Aspirotor (click to enlarge)
Wind powered mechanical chimney draught
Driven by the wind to improve the draught and prevent any down draught. Used for every fuel type and it can be fitted to a metal chimney for new build installations and also to a clay pot for property refurbishments.
Suitable for chimney diameters Ø125 up to Ø250.
Exodraft (click to enlarge)
Electrical powered mechanical chimney fan
This is the ideal draft improvement solution when a naturally self-venting chimney or flue is impossible or difficult to achieve. Used for every fuel type and can be fixed to all types of chimney in new installation or property renovations.
Can be supplied with all the necessary accessories and controls to guarantee the correct chimney draught.
Regul’Art (click to enlarge)
Designed draught stabiliser
Regul’Art allows a bespoke decoration to match your interior.
Draught stabilisers are secondary air inlets fitted to the chimney. By allowing additional outside air to enter the system, these inlets regulate the pressure inside the chimney.
A draught stabiliser saves energy and money by equalising pressure fluctuations inside the chimney and thus lowering fuel consumption.
High quality hot air recovery and warm air distribution system
The COMFORT+ Warm Air Distribution system is a recovery of hot air via a chimney heat exchanger which consists of taking the heat produced by a stove and distributing it to selected rooms.
Your stove provides the heating to your living room, the COMFORT+ system supplies additional free heat to the rest of your home.
It is available in 3 diameters (Ø130, Ø150 & Ø180).